Differences

This shows you the differences between two versions of the page.

--- astra_conv:conversion:cooling_system:cooling_system [2014/04/22 21:48]
richard
+++ astra_conv:conversion:cooling_system:cooling_system [2014/04/23 20:05]
richard
@@ Line 3: / Line 3: @@
 ====== cooling system  ======
-As mentioned before, the motor is foreseen for liquid cooling. Although it can even be operated without, cooling is a safety measure to prevent that the controller throttles down the motor at persistently high load, especially in hot weather.
+As mentioned before, the motor is fitted for liquid cooling. Although it can even be operated "dry", cooling  prevents that the controller throttles down the motor at persistently high load, especially in hot weather.
 In contrast to the motor, the controller is air cooled. It also tends to overheat under harsh conditions, so the cooling system includes forced air cooling of the controller. The cooler fan of the air conditioning system is reused for this purpose.
@@ Line 52: / Line 52: @@
 {{:astra_conv:conversion:motor_cooler:p1110277.jpg?500|}}
+Temperature sensors - The double sensor is glued to the motor, one of the NTCs is for the cooler controller itself, the output of the other one is relayed to the temperature gauge in the dashboard (as long as the coolant heater is off).
+The NTC sensor for the motor controller is fitted into a cable shoe and bolted to the motor controller's heat sink.
+{{:astra_conv:conversion:motor_cooler:p1110717.jpg?340|}} {{:astra_conv:conversion:motor_cooler:p1110879.jpg?340|}}
@@ Line 99: / Line 105: @@
-The liquid cooling circuit consists of the motor itself, a small cooler from a Honda 250 scooter and a circulation pump. Together with the heater circuit (which runs independently and has its own circulation pump), the cooling circuit is connected to the original coolant liquid reservoir. The air buffer in the reservoir will take up thermal expansion of the coolant liquid, and it can be pressurized to ease refilling and emptying of the two circuits.
+The coolant liquid is circulated by an electric pump, through the motor and though a small radiator. Together with the heater circuit (which runs independently and has its own circulation pump), the cooling circuit is connected to the original coolant liquid reservoir. The air buffer in the reservoir will take up thermal expansion of the coolant liquid, and it can be pressurized to ease refilling and emptying of the two circuits.
+Overview of the cooling system's components, ready for installing:
+{{:astra_conv:conversion:motor_cooler:p1110736.jpg?800|}}
 The cooler got a place near the front grille, at the passenger side. From it's scooter past, it already has a small fan attached.
 {{:astra_conv:conversion:motor_cooler:p1110310.jpg?770|}}
+{{:astra_conv:conversion:motor_cooler:p1110885.jpg?770|}}
 DIY bleeder screw at the top of the cooler:
@@ Line 109: / Line 121: @@
 {{:astra_conv:conversion:motor_cooler:p1110255.jpg?340|}} {{:astra_conv:conversion:motor_cooler:p1110256.jpg?340|}}
+Coolant terminals on the motor. Please note that the fittings used in below foto turned out not to be tight - I have replaced them later. The new fittings have a flange to press a rubber gasket against the motor's case.
+{{:astra_conv:conversion:drivetrain:P1100856.jpg?600|}}
+The coolant pump (again a Volkswagen Vanagon Turbo Diesel circulation pump, as for the heater circuit). This recent model by the way has a brushless motor with magnetic coupling to the pump chamber. It runs on very low current and appears quite long-lasting.
+{{:astra_conv:conversion:motor_cooler:p1110884.jpg?600|}}
+As usual, every component has its own flange diameter, and I needed to solder a couple of adapters. To start with, it is always good to have a plan of the puzzle:
+{{:astra_conv:conversion:motor_cooler:p1110719.jpg?600|}}
+The first picture shows two mistaken ones, corrected in the second picture. Note the additional small diameter pipe on one of the adapters. It connects the cooling circuit to the coolant reservoir via a thin hose.
+{{:astra_conv:conversion:motor_cooler:p1110734.jpg?340|}} {{:astra_conv:conversion:motor_cooler:p1110880.jpg?340|}}
+Testing cooler and fittings for tightness:
+{{:astra_conv:conversion:motor_cooler:p1110732.jpg?600|}}

User Tools

Site Tools

Differences

Page Tools